PRODUCT DEFINITION<\/b>
\nA single-component granite and marble adhesive mortar based on cement, with reduced slip properties and performance-enhancing additives.<\/p>\n
ADVANTAGES<\/b>
\n– Easy to apply
\n– Does not sag in vertical applications
\n– Reinforced formula<\/p>\n
APPLICATION AREA<\/b>
\n– Used for bonding ceramics with a water absorption rate below 5%, as well as materials such as granite ceramics and marble.
\n– Please consult us for all other applications.<\/p>\n
APPLICATION PROPERTIES<\/b>
\nUsable Time: Max 3 hours
\nWorking Time: Max 20 min
\nAdjustment Time: Max 10 min
\nJoint application time: 24 hours on walls, 48 hours on floors
\nTraffic Opening Time: 48 hours
\nApplication Thickness: 4-12 mm (single or double-sided application)<\/p>\n
REFERENCE STANDARDS<\/b>
\nTS EN 12004-1 \/ C2T class<\/p>\n
QUALITY CERTIFICATES<\/b>
\nCE<\/p>\n
PERFORMANCE INFORMATION<\/b>
\nInitial tensile adhesion strength \u22651 N\/mm\u00b2 (TS EN 1348)
\nTensile adhesion strength after immersion in water \u22651 N\/mm\u00b2 (TS EN 1348)
\nTensile adhesion strength after heat aging \u22651 N\/mm\u00b2 (TS EN 1348)
\nTensile adhesion strength after freeze-thaw cycles \u22651 N\/mm\u00b2 (TS EN 1348)
\nTensile adhesion strength after open waiting time (20 min later) \u22650.5 N\/mm\u00b2 (TS EN 1346)
\nSlip \u22640.5 mm (TS EN 1308)
\nFire Reaction Class: A1 (TS EN 13501-1)
\nNote: Values were obtained in a laboratory environment at 23\u00b12\u00b0C and 50% relative humidity after 28 days. May vary depending on site conditions.<\/i><\/p>\n
WARNINGS AND RECOMMENDATIONS<\/b>
\n– No foreign materials should be added.
\n– All tools used should be washed with water before drying.
\n– Water should not be added to mortar that has passed its use-by date for reuse.<\/p>\n
SURFACE PREPARATION<\/b>
\n– The surface should be clean, dry, smooth, and sound.
\n– Plasters thinner than 3 mm should be scraped off.
\n– Any roughness that may reduce adhesion should be removed.
\n– Defects should be repaired with Allkim Flex Repair Mortar at least 24 hours before application.
\n– Porous surfaces should be moistened, but no water film should remain on the surface.
\n– Repairs under 7 mm can be made with Allkim Flex Granite and Marble Adhesive.
\n– On raw concrete surfaces, ALLASTAR raw concrete primer should be applied in a single coat.<\/p>\n
APPLICATION CONDITIONS<\/b>
\n– Ambient temperature should be between +5\u00b0C and +35\u00b0C.
\n– Should not be applied on frozen surfaces or surfaces at risk of freezing within 24 hours.
\n– Should not be applied in direct sunlight, strong wind, or on hot surfaces.
\n– Surfaces with a film layer should be re-scraped.<\/p>\n
APPLICATION INSTRUCTIONS<\/b>
\n– Slowly pour 25 kg of powdered mortar into 6.5-7 liters of water and mix with a low-speed mixer.
\n– Let it rest for 5-10 minutes, then mix again.
\n– Har\u00e7, di\u015fli \u00e7elik mala ile y\u00fczeye uygulan\u0131r, mala di\u015f boyutu seramik \u00f6l\u00e7\u00fcs\u00fcne g\u00f6re se\u00e7ilir.
\n– For large-sized ceramic tiles, double-sided bonding should be performed.
\n– Air pockets should be removed by pressing with a rubber mallet.
\n– The prepared mixture should be used within 3 hours.
\n– Grout filling should be done 2 days after installation on the floor and 24 hours after installation on the wall.<\/p>\n
PACKAGING<\/b>
\n25 kg bag (60 bags per pallet, 1500 kg)<\/p>\n
PALLET DIMENSIONS<\/b>
\n80×110 cm<\/p>\n
COLOR<\/b>
\nWhite, gray<\/p>\n
APPLICATION TOOLS<\/b>
\nHand mixer, trowel, rubber mallet, notched steel trowel<\/p>\n
SHELF LIFE<\/b>
\n1 year from the date of manufacture in a dry environment free of moisture<\/p>\n","protected":false},"featured_media":1311,"template":"","products-category":[107],"class_list":["post-6164","products","type-products","status-publish","has-post-thumbnail","hentry","products-category-allkim"],"yoast_head":"\n