Tile and Ceramic Adhesive
Product Definition
- A single-component tile and ceramic adhesive mortar based on cement, with reduced slip properties and performance-enhancing additives.
- Easy application
- Does not sag in vertical applications
- Reinforced formula
- Used for ceramic, tile, and other covering materials on interior walls and floors, and exterior flooring.
- Consult us for all other applications.
- Not suitable for high-traffic areas (industrial areas, etc.). ALLKİM EXTRA Flex should be used instead.
- Not suitable for prefabricated and underfloor heated flooring. Instead, Allkim EXTRA Flex Granite and Marble Adhesive Mortar should be used.
Reference Standards
- TS EN 12004-1 / C1T class
Quality Certificates
- TS EN 12004-1
- CE
25 kg bag (60 bags per pallet, 1500 kg)
Pallet Dimensions80 x 110 cm
ColorWhite, gray
Application ToolsHand mixer, trowel, rubber mallet, notched steel trowel
Shelf Life- 1 year from the date of manufacture in a dry environment
- When not in use, the packaging should be tightly closed
These values were obtained in a laboratory environment and may vary under site conditions.
Warnings and Recommendations- No foreign materials should be added under any circumstances.
- All tools used should be washed with water before drying.
- Mortar that has passed its use-by date should not be reused.
- The surface must be clean, dry, smooth, and solid; plaster thinner than 3 mm should be scraped off.
- It should be free of roughness that could reduce adhesion.
- Significant defects or holes should be repaired with Alser Repair Mortar at least 24 hours in advance.
- Porous surfaces should be moistened and allowed to remain damp.
- Repairs under 7 mm can be made with Alser Tile and Ceramic Adhesive.
- Bare concrete surfaces should be primed with one coat of ALLASTAR primer.
- Ambient temperature between +5 °C and +35 °C.
- Should not be applied on frozen, thawing, or surfaces at risk of freezing within 24 hours.
- Should not be applied in direct sunlight, strong wind, or on hot surfaces.
- The mortar should not form a film on the surface. If a film forms, it should be re-troweled.
- Slowly pour 25 kg of powder into 6.5-7 liters of water and mix thoroughly with a low-speed mixer.
- Let it rest for 5-10 minutes, then mix again.
- Apply the mortar to the surface, adjusting the thickness with a notched steel trowel.
- Double-sided bonding should be used on floors larger than 1100 cm², walls larger than 900 cm², and all outdoor applications.
- Air should be expelled by applying force with a rubber mallet.
- Tiles must be adhered within 20 minutes.
- The prepared mortar must be used within 3 hours at the latest.
- Grout filling should be done after 2 days on the floor and 24 hours on the wall.
Technical Specifications
Ceramic Trowel Consumption
| 120 cm² (6x6x6 mm) | Single-sided: 3 kg/m² Double-sided: 4.5-5 kg/m² |
| 120-500 cm² (8x8x8 mm) | Single-sided: 4 kg/m² Double-sided: 6-7 kg/m² |
| 500-2000 cm² (10x10x10 mm) | Single-sided: 5.5 kg/m² Double-sided: 7-8 kg/m² |
| Usable Time | Max 3 hours |
| Working Time | Max 20 min |
| Adjustment Time | Max 15 min |
| Joint Application Time | 24 hours on walls, 48 hours on floors |
| Traffic Opening Time | 48 hours |
| Application Thickness | 4-12 mm (single or double-sided) |
Performance Information
| Initial tensile adhesion strength | ≥0.5 N/mm² (TS EN 1348) |
| Tensile adhesion strength after immersion in water | ≥0.5 N/mm² (TS EN 1348) |
| Tensile adhesion strength after heat aging | ≥0.5 N/mm² (TS EN 1348) |
| Tensile adhesion strength after freeze-thaw cycles | ≥0.5 N/mm² (TS EN 1348) |
| Tensile adhesion strength after open time (after 20 min) | ≥0.5 N/mm² (TS EN 1346) |
| Slip | ≤0.5 mm (TS EN 1308) |
| Fire Reaction Class | A1 (TS EN 13501-1) |
Technical Information
| Application Thickness | 0.3 mm |
| Density | 1.52 kg/liter |
| Drying Time | 90 minutes |
Mixing Ratios
| Allastar | 12 kg |
| Water | 2.5-3.5 liters |
| Mix Density | 1.32 kg/liter |
