Thermal Insulation Board Plaster
DEFINITION
Cement-based, fiber and polymer reinforced, high-performance thermal insulation board plaster.
AREAS OF USE- As plaster on polystyrene boards (XPS; Extruded Polystyrene or EPS; Expanded Polystyrene),
- For repair purposes; at the joints of main structural elements.
- Stone wool
- For corner and parapet cracks.
- For plastering purposes (up to 5 mm).
- On aerated concrete surfaces.
- As a thin plaster over rough plaster.
- Provides high adhesion to thermal insulation boards.
- Allows the system to breathe due to its vapor permeability.
- Provides easy and long-term working conditions.
- Provides a smooth and aesthetic appearance on interior and exterior surfaces.
- Absorbs small stresses.
- Minimizes crack formation with fiber and polymer reinforcement.
- Form: Cement-based, fiber and polymer-reinforced powder
- Color: Gray
- Packaging: 25 kg kraft bag
- Shelf Life: 12 months in a dry environment without moisture
- Unit Weight: 1300 ±100 g/lt
- Usable Time of the Mortar: 2 - 2.5 hours
- Working Time: 25 min
- Application Thickness: 3 - 5 mm
The panel to be applied must be properly adhered to the substrate.
Gaps between panels must be filled appropriately, and the surface must be smooth.
APPLICATIONPour 6-7 liters of water into a clean container large enough to hold one bag. Slowly add Allkim Flex Thermal Insulation Panel Mortar to the water and mix with a low-speed mixer until a homogeneous mixture is obtained. After the mixed mortar has rested for 5 minutes, it is mixed again for 1-2 minutes and made ready for use. The prepared mortar is applied to the thermal insulation boards with a thickness of 2 mm, and plaster mesh is laid to ensure adhesion to the surface. To prevent cracking, the reinforcement mesh should be applied overlapping by 10 cm at the joints. Then, a second coat of fine plaster is applied with a thickness of 2 mm. The material, which has started to harden, is smoothed and troweled.
APPLICATION TOOLSHand mixer, steel trowel, spatula, rubber trowel
SHELF LIFE1 year from the date of manufacture in dry and moisture-free conditions.
CONSUMPTIONDepending on the surface to be applied and the thickness, 4-5 kg/m² for a thickness of 3-4 mm.
WARNINGS AND PRECAUTIONS- The application temperature should be between +5 ⁰C and +35 ⁰C.
- Avoid application in very humid and very hot weather.
- Do not apply on surfaces where there is a risk of frost.
- After plaster application, the surface should be moistened at regular intervals.
- Coating, painting, and similar applications should begin 7 days after plaster application.
- Avoid prolonged contact of the material with eyes and skin, and do not inhale dust from the material.
- All tools used should be cleaned with water before they dry.
- The information provided is valid for application areas with a temperature of 23 ± 2 ⁰C and humidity of 50 ± 5%.
25 kg kraft bags (64 bags per pallet, 1600 kg)
Technical Specifications
PERFORMANCE INFORMATION
| Standard Type | TS 13687 |
| Density (Unit volume mass of fresh mortar) | ≥ 1150 kg/m³ |
| Sieve Analysis (residue on 1 mm sieve) | ≤ 1% |
| Flexural Strength | ≥ 2 N/mm² |
| Compressive Strength | ≥ 6 N/mm² |
| Adhesion Strength to Thermal Insulation Board | ≥ 0.08 N/mm² |
| Water Absorption | ≤ 0.5 kg/m² minute0.5 |
| Water Vapor Permeability Coefficient | µ ≤ 15 |
| Thermal Conductivity | ≤ 0.47 W/mK |
| Fire Reaction Class | A1 |
